INFOCUS 4805 SERVICE MANUAL PDF

Projector InFocus ScreenPlay User Manual . (see page 40) replace lamp When sending the projector in for repair, we recommend shipping the unit in its. Products 1 – of the right to download the INFOCUS LP70+ user manual Infocus Lp infocus lp service manual infocus projector infocus. And now my latest problem: My Infocus SP DLP projector from has Also attached is the service manual for the X1 which is similar.

Author: Vudorisar Zukora
Country: Grenada
Language: English (Spanish)
Genre: Marketing
Published (Last): 6 February 2018
Pages: 318
PDF File Size: 11.23 Mb
ePub File Size: 19.1 Mb
ISBN: 484-5-43503-643-8
Downloads: 39544
Price: Free* [*Free Regsitration Required]
Uploader: Fenrizuru

InFocus SP4805 User Manual

It should have plenty of hours left on it. Posted on Nov 29, To inrocus, point the remote at the projection screen or at the projector not at the video device or computer. If necessary, rotate the leveling foot located at the rear of the projector. I don’t have a usb cabel for my camera yet, but I did take some pictures of the entire operation, I will post them here once my lazy ass has moved itself down to get a cable. Basically, you can’t know that your ballast is good without a certified good bulb and you can’t know that you have a good bulb unless you know you have a good ballast Ihfocus for a little post mortum Infocus SP powers on but no lamp X But it is very important that the alignment is maintained the entire length.

Can anyone offer any suggestions? Adjust the zoom and focus. Take note of the error code and make the appropriate fixes. The color wheel has to be removed to get to the light tunnel The light tunnel is very fragile and easily broken. InFocus repairs are extremely costly and very problematic if you live in europe.

  ABRAMOVICH STEGUN PDF

InFocus repairshop – AVS Forum | Home Theater Discussions And Reviews

I messed with it some more and noticed that after awhile it would twitch more and more and eventually spin up to full speed for a few seconds and then stop. Mar 13, Kenwood Food Mixers. I replaced all of the ‘lytic caps including the filter cap on the power supply board but it still behaves the same.

Hi there, Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two. Final scoreboard on the swap: Apparently it has a speed sensor and will not light the lamp if the color wheel is not spinning at the right speed.

It should be noted that the bulb was cold as the projector had been on for approximately 5 minutes before all of this happened. So I hooked up the original components on the bench and did a firmware re-flash. Is there any other way to test the lamp? DO NOT touch the bulb with bare fingers. Basically, I think you have a “used up lamp”.

Then I turned it off and wiglled all the cables. Anyone who has successfully done this, please help.

After not getting servive picture while trying to connect the TV Box with theI got sidetracked and came across the “source enable” p38 in the manual and decided I did not need anything selected so I deselected “component” I had selected for my DVD player long ago and the lamp immediately turned off and the keyboard and remote no longer work!!!!

  BIOCHEMIJOS LABORATORINIAI DARBAI PDF

Replace the lamp door.

Infocus 4805 Troubleshooting

Problem with my projector. Just under it there’s a small aluminium thingy holding the light tunnel in place the light tunnel is 4 small pieces of mirror glued together. This is annoying though, what causes this? Presets—cycles through the available preset settings page It should come up to speed relatively quickly Table of Contents Add to my manuals Add.

This allows you to customize settings and save the settings to be restored later. The following manal options are only available for composite, S-video, or component i sources. Don’t show me this message again.

Still no signs of life from the lamp. Originally Posted by vidvandre Hello Ulvin I am experiencing this problem now, just after changing the lamp: William Pullman is a freelance writer from New Jersey.

So I ordered a new filter cap and one more Panny FC to replace the last suscon. The bulb hour counter was reset once or twice, so I don’t know the true count but I’d guess I’m at around on the original bulb.