EN 10243-1 PDF

DIN EN – Free download as PDF File .pdf), Text File .txt) or read online for free. Find the most up-to-date version of DIN EN at Engineering Buy DIN EN STEEL DIE FORGINGS – TOLERANCES ON DIMENSIONS – PART 1: DROP AND VERTICAL PRESS FORGINGS.

Author: Kazralkree Melrajas
Country: Uzbekistan
Language: English (Spanish)
Genre: Literature
Published (Last): 26 February 2007
Pages: 57
PDF File Size: 9.2 Mb
ePub File Size: 5.12 Mb
ISBN: 201-3-66417-308-3
Downloads: 94792
Price: Free* [*Free Regsitration Required]
Uploader: Dinris

The permissible length of local deviation from the bar stock diameter or section adjoining a forged portion shall be up to 1,5 times the bar stock diameter or largest cross-sectional dimension, but with a maximum value of mm see Figure They are classified into four groups; accordingly each of them is displayed in the 12043-1. The tolerances specified apply to forgings not exceeding kg in mass or 2 mm maximum dimension.

This grade should not be specified unless the additional forging cost entailed can be justified by a consequent saving in overall cost. Requirements for carbon, carbon manganese and alloy hot worked or cold finished steels.

This European Standard is considered to be a supporting standard to those application and product standards which in themselves support an essential safety requirement of a New Approach Directive and which make reference to this European Standard. Ejector mark tolerances are applied independently of, and in addition to, any other tolerances. Formula for calculating mismatch: On forged surfaces which are not machined subsequently, scale pits and surface dressing shall be permitted to a depth equal to one-third of the total value of the thickness tolerance.

ISO enn, Technical drawings Fundamental tolerancing principle.

In extreme cases they can cover the whole field of tolerances unless otherwise agreed between the supplier and the purchaser. In the latter case the tolerances shall be indicated against the appropriate dimension on the forging drawing.

Instances occur in which this tolerance is inadequate. Drop and vertical press forgingsrgees par estampage en acier es dimensionnelles Pieces executees a chaud sur x-pilons ou presses verticalesGesenkschmiedeteile aus Stahl MatoTeil 1: Instances occur in which the negative tolerances for such local deviations 10234-1 be permitted on unforged stock where it is not subsequently machined. A version in any other language made by translation 1024-1 the responsibility of a CEN member into its own language and notified to the Central Secretariat has the English versionSteel die forgings Tolerances on dimensions Part 1: The cost of the forged part can be higher if grade E tolerances are selected, but the need dn subsequent machining operations can often be reduced.

  CURSO PIC 16F628A PDF

Tolerances for fillet and edge radii shown in Table 6 are applicable to both grade 10243- and grade F. Figure 16 Dimensions to dn centre-to-centre tolerances are not applicable other than by negotiation Figure 17 Fillet and edge radii16 BSI 12 January Burr tolerances are applied independently of, and in addition to, any other tolerances. Above 0,63 up to and including 1. The weight of the total length in question shall be calculated as if of unforged stock, irrespective of whether this is the case or not.

The nominal diameter and the location of ejector marks will be indicated to the purchaser on the forging drawing before the 102243-1 of production. The minus tolerances do not apply to edge radii up to and including 3 mm when such radii are affected by subsequent removal of draft by trimming or punching. Also, the deviations of form do not include scale pits and depth of surface dressing see 5.

EN 10243-1.pdf

Accept and continue Learn more about the cookies we use and how to change your settings. The location of burrs shall be indicated to the purchaser on the forging drawing for approval before the commencement of production. Learn more about the cookies we use and how to change your settings.

Flatness tolerances relate to deviations of surfaces from the specified contour. The residual flash is measured from the body of the forging to the trimmed edge of the flash, as indicated in Figure For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision.

BS EN 10243-1:1999

To determine the category in which a steel belongs, the maximum permitted content of the elements in the steel specification shall be the values used. Amendments issued since publicationAmd. Permissible tolerances based on the greatest dimensions are usually obtained from the appropriate table Maximum length: Straightness and flatness tolerances are applied independently of, and in addition to, any other tolerances.

Take the smart route to manage medical device compliance. These marks may be either sunken or raised. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member.

  CARACTERISTICAS DE LAS ESPERMATOFITAS PDF

BS EN – Steel die forgings. Tolerances on dimensions. Drop and vertical press forgings

See also Figure Examples are shown of circular and non-circular forgings see Figure 2 and Figure 3. This approach will ensure that optimum use is made of the forging process in fulfilling the purchaser’s special requirements at the lowest additional cost. A similar procedure is followed for the factor of shape complexity so that downward displacement of the horizontal line used is nil, one place, two places and three places for factors S1, S2, S3 and S4 respectively.

When no tolerance is indicated against the dimension concerned, the tolerance for the maximum length or 1023-1 of the forging shall be applied from Table 1 or Table 2but the dispersion will be plus and minus one-half of the total tolerance, and not as shown in the tables. In measuring mismatch, accuracy depends upon making due allowance for surplus metal caused by uneven die wear.

You may experience issues viewing this site in Internet Explorer 9, 10 or Users are responsible for its correct application. The tolerance grade and tolerances given on the drawings are examples only and should not be regarded as either mandatory, recommended or minimum requirements since in practice the tolerances will depend on both the capability of the forging equipment and the requirements of the purchaser.

Example of the use of Table 1 Forging grade F for determining the tolerances for length, width, height dimensions of a forging.

Types of inspection documents PD All variations in thickness, due to die-closure, die-wear and shrinkage are included in the thickness tolerances. When tolerances for rn ends are required, this will be indicated to the purchaser on the forging drawing before the commencement of production.

Summary of pagesThis document comprises a front cover, an inside front cover, the EN title page, pages 2 to 34, an inside back cover and a back cover. In such cases it can be arranged by negotiation between the purchaser and the supplier that the entire tolerance is shown as a positive one.