Error Codes List of Error Codes The machine is equipped with a mechanism to run self diagnosis to find out its condition (particularly of its sensors): CPU on. These are all list of error code in Canon iR/iR more to come, i hope your machines works fine and never get error. E Main cause. Canon IR Manual Online: Error Codes, List Of Error Codes. List Of Error Codes The Machine Is Equipped With A Mechanism To Run Self Diagnosis To Find Out Its Condition (particularly Of Its Copier Canon IR Quick Manual.
|Published (Last):||10 March 2012|
|PDF File Size:||15.42 Mb|
|ePub File Size:||2.12 Mb|
|Price:||Free* [*Free Regsitration Required]|
After replacing the fixing web, be sure to reset the two web counters in service mode: The copy data controller or the remote diagnostic device is faulty. The punch motor M1P is faulty. The heat discharge fan FM3 is faulty. The stitch motor front, M7S is faulty.
Main Cause The various printer cabon accessories are faulty. The finisher controller PCB isfaulty. The potential measurement PCB is faulty. Mode ofDetection The guide home position sensor does not turn on when the guidemotor has been driven for about 0. The remote diagnostic device PCBis faulty. The thermal switch TP1 has an open circuit. Main cause The connector has poor contact. The paper push-on platehome position sensor PI14S is faulty.
The tray upper limit detecting switch MS5 is faulty. Mode ofDetection An error has occurred in the communication between the various.
The controller cooling fan FM4 is faulty. The stapler motor M6 is faulty. Mode ofDetection The paper push-on plate home position sensor does not turn onwhen the paper push-on plate motor has been driven for 0.
The copy data controller orthe remote diagnostic device is faulty. Main Cause The alignment plate home position sensor PI6 is faulty. The scanning lamp xenon tube is faulty. The paper folding homeposition sensor PI21S is faulty. About me indra Indonesia Just want to share View my complete profile.
The safety codew detecting switch MS3 is faulty. The fixing web length sensor PS45 is faulty.
Error Code Canon IR error E
Main cause The LAN card is faulty. Mode ofDetection While the machine is in standby, the communication with the hostmachine has been interrupted for 5 secs or more. The sub thermistor TH2 has detected overheating. The hard disk drive isfaulty.
The scanner motor M3 is faulty. The scanner HP sensor PS39 is faulty. The swing guide open sensor PI18 is faulty. Main Cause The hard disk fan FM7 is id6000. The primary charging assemblycooling fan FM2 is faulty. Main Cause The tray home position sensor PI8 is faulty. Main Cause The stapler home position detecting switch MS7 is faulty. The paper push-on plate leadingedge position sensor PI15S is faulty.
The puncherdriver PCB is faulty. The communication line has an opencircuit. The DC power supply fan FM6 is faulty. Mode ofDetection The number of erro pulses of the folding motor clock sensordrops below a specific value. Subscribe in a reader. The fixing web has been taken up. Mode ofDetection The communication between the host machine and the finisher hasbeen interrupted; this error is detected by the host machine.
Mode ofDetection The alignment plate does not leave home position when the alignmentmotor has been driven for 2 secs. The folding motor M2S is faulty. Mode ofDetection The errorr home position sensor front does not turn off when thestitch motor front has been rotated Codrs for 0. Main Cause The shutter open sensor PI5 is faulty.
Canon iR5000 Service Manual: Error Codes; List Of Error Codes
The lamp inverter PCB is faulty. The saddle stitcher controller PCB is faulty. The coin vendor is faulty. The SSR has a short circuit.
The swing motor M7 is faulty. The saddle stitcher controllerPCB is faulty. Mode ofDetection The puncher does not leave home position when the punch motorhas been driven for msecs. Mode of Detection When the host machine’s power switch is turned on, the backupdata of the EEPROM cannot be read or the data, if read, has an error. The drum motor M1 is faulty.